Draftsight 2016 activate failure12/20/2023 ![]() The online activation system is a new feature that is only available with SOLIDWORKS 2018. To avoid performing a manual license transfer, you can change your SOLIDWORKS activation type from machine activation to online activation. In this case, a temporay license can be provided to cover the time of repair to your machine. Therefore if you computer has crashed and been sent to IT for repair, you won’t need a license disable request as you will be using this computer for SOLIDWORKS again once it is repaired. The license disable request will disable the old Computer ID for using the particular SOLIDWORKS license in question. If you have replaced your motherboard, reinstalled Windows, or replaced the hard drive and the old hard drive is not accessible, then you will need to contact our Technical Support team to request a license disable request. Then you should be able to launch SOLIDWORKS and deactivate the license from there, as per the above. If you have replaced your hard drive, you will need to plug the old hard drive back in to the machine, and start Windows system from there. If you have performed a computer hardware/ software change and are receiving this activation error, please follow the steps below:įirst of all, the steps you take to fix the problem will depend on what changes have been made on your machine. Then you can follow the prompts to get the license deactivated:Īfter this, you should be able to launch SOLIDWORKS and follow the prompts to activate the license on the new machine. if you forget to transfer a license off an old machine before activating it on a new machine, you can access the machine that has the license activated, launch SOLIDWORKS, and go to “Help” > “Deactivate license(s)”. Performing a change to the Computer hardware/software which caused the Computer ID change, so the license is still activated on the old Computer ID (even on the same machine). Failing to transfer the license from the current activated machine before activating the license on a new machine. ![]() Therefore, there are 2 common reasons to cause a license activation failure: Each of the machine will be given a particular Computer ID which is generated from a combination of the motherboard mac address, hard drive ID and Windows ID. The SOLIDWORKS activation portal is using the Computer ID to identify the machines on which a particular licence is activated. ![]() We call this process transferring a licence. You then need to activate your licence on the machine on which you wish to continue working. Therefore, to use SOLIDWORKS on a different machine, you will need to deactivate your license from the machine where the license is currently activated. However, a licence can only be activated on one machine at a time. SOLIDWORKS licenses (including standalone and network) can be used for more than one installation. This article will help you to understand how SOLIDWORKS license works and trouble shoot this particular error. I’ve run ‘ nslookup -type=srv _vlmcs._tcp’ on the client and it can see the KMS host that is supposed to be servicing ‘Office 2016’ activations.If you are transferring your SOLIDWORKS licenses frequently, you may have seen the error message “Activation count exceeded” for one of your SOLIDWORKS license activations. The count on the KMS host hasn’t increased by one either. To view the activation event history run: cscript OSPP.VBS /dhistorykms NOTICE: A KB article has been detected for activation failure: 0xC004F074 FOR MORE INFORMATION PLEASE VISIT: ![]() Please see the Application Event Log for additional information. No Key Management Service (KMS) could be contacted. Installed product key detected - attempting to activate the following product: SKU ID: d450596f-894d-49e0-966a-fd39ed4c4c64 LICENSE NAME: Office 16, Office16ProPlusVL_KMS_Client edition LICENSE DESCRIPTION: Office 16, VOLUME_KMSCLIENT channel Last 5 characters of installed product key: WFG99 ERROR CODE: 0xC004F074 ERROR DESCRIPTION: The Software Licensing Service reported that the product could not be activated. However, the KMS activation is failing on the client with the following error. I’ve tried testing the KMS host by converting an ‘Office 2016’ installation on a client from MAK to KMS activation following the article below. Both installed and activated successfully with their respective CSVLK keys on the KMS I’ve installed the ‘ Office 2010 KMS Host License Pack’ (V.5000) and the ‘ Office 2016 Volume License Pack’ (V.1002). I’ve recently set up a ‘Windows 2012 Standard R2’ server as a KMS host.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |